Izdelki za proizvajalci masti (8)

625 CXF Ein Hochleistungsfett mit Korrosionsinhibitoren und ausgezeichneten Hochdruckeigenschaften sowie erstklassigem Widerstand gegen Auswaschen durch Wasser. Erstklassiger Widerstand gegen Auswaschen durch Wasser Ausgezeichneter Korrosionsschutz Ist mit den meisten Fetten verträglich Ausgezeichnete Scherstabilität Antioxidanzien verhindern Aushärtung oder Kristallisierung Erhältliche Behältergrößen: Sprühdose (nur 630 SXCF), 400 g, 18 kg, 55 kg, 180 kg

Standard multi-purpose grease based on lithium soap for rolling and plain bearings. Specification releases: K 2 K-30 Product number:1630131 Container size:1 Product group:Fats in general

Schmierstoffe Reinigung und Entfettung Hilfsmittel und Spezialitäten Reinigungsgeräte Wartungsprodukte: Schmierfette Reinigungsmittel Entfetter Schmierstoffe

Unsere Getriebeöle bieten zuverlässige Leistung, dauerhaften Schutz und eine lange Ölstandzeit bei weniger Energieverbrauch. Die Herstellerspezifikationen und Freigaben sind zu beachten.

Syntech HAG Acryl Syntech HAG Acryl is a four-component resin that reacts to form an elastic and durable gel. The properties of Syntech HAG Acryl are: • Good general chemical resistance. • Does not contain acrylamide, methacrylamide, formaldehyde or solvents. • Not inflammable. • Excellent adhesion on mineral building materials such as concrete, cement and bricks. • The reaction speed can be adjusted from a few seconds to several minutes. • When the injected cracks dry out due to temperature or groundwater level fluctuations the gel does not crack easily. • The hardened gel has excellent durability in wet-dry cycles. Syntech HAG Acryl components are supplied ready to use. Create 2 mixes in separate plastic buckets. Prepare only the quantity to be used each time. Solution 1: Syntech HAG Acryl component A (25 kg resin) mixed with Syntech HAG Acryl component B (2.5 kg catalyst). Solution 2: Syntech HAG Acryl component C (2 packs of 0.625 kg) mixed with clean tap water. Attention: The amount of water must be equal in volume to solution 1. When mixing resin, always use a wooden or stainless steel spatula. The reaction time depends on the temperature of the material, the structure of the building and the possible amount of water present. Higher temperature will speed up the reaction time and lower temperature will slow it down. It is advisable to carry out an on-site test, before injection, to observe and define the reaction time. To change the reaction time, only adjust the amount of Syntech HAG Acryl component C. The amount of the other components remains the same. Use a two-component stainless steel pump (manual, electric or pneumatic). Check that the pump and equipment are clean and that there is no residue from previous injection work. The two mixtures are fed into the pump separately, but are mixed homogeneously at a volumetric ratio of 1:1 in the pump's mixing head, before being injected through the pump nozzle. Check the quality of the concrete, as injection involves pressure. Sealing and waterproofing of cracks and cavities in walls, floors, concrete constructions, underground structures, etc. It can be used in constructions that are not permanently in contact with water (fluctuating groundwater level). Injection of very fine cracks. Determine the type and size of packers based on your pump and injection type. If reinforcing steel is present, try to locate it and plan the drilling pattern so that the reinforcement is not drilled. Drill holes at an angle of approximately 45° or less and in the direction of the crack. Make sure the hole goes through the crack. The distance of the drilled holes depends on the width of the crack. Place the packer in the hole. Prepare the pump to start the injection. The injection pressure varies depending on the structure and size of the crack. Start the injection at the lowest point of the crack. Continue injecting until resin flows out of adjacent packer(s). This is necessary to achieve uniform distribution of the material. Stop pumping, unplug and move on to the next packer. Continue the procedure until the crack is completely filled. After the material has cured, the packers can be removed. Holes drilled can be covered with Repar Tix Speedy HP quick-setting mortar. Clean and rinse the pump equipment with water whenever there is a stoppage longer than 15 minutes and, after completing the injection, rinse with a sufficient amount of water. Make sure the pump is clean and stop only when clean water comes out of the pump. The consumption of the product depends on the size of the empty volume to be filled. Can 25 kg [A] - Plastic can 2.5 kg [B] - Canister 0.625 kg [C] - Canister 0.625 kg [D] - Kit: 1 Can 25 kg [A] + 1 Plastic can 2.5 kg [B] + 1 Canister 0.625 kg [C] + 1 Canister 0.625 kg [D]

Référence GCINCOPISFIN-1KG

Universal grease Description Lithium-saponified universal grease based on high-quality mineral oils with selected ingredients. Has anti-wear, anti-aging and anti-corrosion components Universal lubricant/grease for a wide range of applications , among others. in the passenger car sector with approval from the automotive industry specifications MB-Approval 267.0 DIN - 51502 K2K-30 Product number:1508447 Release:DIN 51502: KP2K-30 Container size:1 Product group:Fats in general

EP Fluid Grease Description Castrol CLS Grease is a high pressure fluid grease developed using an optimized combination of synthetic base oil, lithium thickener technology and a specially selected additive system containing EP/anti-wear additives, antioxidants and corrosion inhibitors. Application Castrol CLS Grease is a high-quality EP fluid grease with excellent low-temperature properties, which makes it particularly suitable for use in central lubrication systems of commercial vehicles and is approved in accordance with the following approvals: - MAN 283 Li-P 00/000 - Mercedes Benz 264.0 Castrol CLS Grease is also used as an excellent multi-purpose fluid grease for industrial and automotive applications where a combination of excellent EP performance and corrosion resistance are the core requirements. Temperature range -40ºC to +100ºC Product number:1620815 Container size:25 Product group:Fluid grease